DRA-SR-RJ45 REV1 Parts List Integrated Circuits - IC's: U1 - CM119A (presoldered) C-Media USB sound controller IC U2 - LM386 JRC386 - audio power amplifier IC U3 - LM386 JRC386 - audio power amplifier IC U4 - NE555 - timer IC Relay: RY1 - SIP-1A05 - 5V high reliability SPST reed relay - nearly silent operation. Diodes: D1 - BAT43 (blue - observe polarity!) D2 - BAT43 (blue - observe polarity!) D3 - 1N4004 - 1N4007 (black - observe polarity!) D4 - 1N4148 (dark orange - observe polarity!) D5 - 1N4148 (dark orange - observe polarity!) D6 - BAT43 (blue - observe polarity!) Chassis Jacks: J1 - RJ45 Female Chassis Connector J2 - USB-B Chassis Jack SJ1 - Speaker Jack (REV2 only) Configuration Headers / Jumpers: These headers are installed so the shorter section is inserted (soldered) into the board JU1 - 3 pin header - green - with shorting bar or "shunt" JU2 - 3 pin header - yellow - with shorting bar or "shunt" JU3 - 2 pin header - blue - with shorting bar or "shunt" JU4 - Not assigned (not used) on this model JU5 - 3 pin header - blue - with shorting bar or "shunt" JU6 - 2 pin header - red - with shorting bar or "shunt" JU7 - 3 pin header - blue - with shorting bar or "shunt" JU8 - 2 pin header - blue - with shorting bar or "shunt" JU9 - 2 pin header - blue - with shorting bar or "shunt" Note: The headers below are not required or included on REV2 and higher boards. These headers are installed so the shorter section is inserted (soldered) into the board. H1 - 4 pin header - white - with jumper H2 - 4 pin header - white - with jumper LEDs: Install absolutely last! LED1 - 3mm Red LED - with short lens to match the length of LED2/3. LED2/3 - multi-color (amber/yellow/green) with clear lens. (Location LED3) The Red LED orients with the short lead in the square hole. The multi-color LED orients with the shortest lead in the square hole. Bend the leads to match the ones on the original circuit board. Use the front panel (by itself) sliding it over the shaft pots and power switch to align the LEDs while soldering in place. IC Sockets: (3) 8 Pin DIP IC Sockets - Note orientation notch - match with silkscreen. (1) 16 Pin DIP Machine Socket located in the "Configuration Socket" location beside the RJ45 radio connector. (8) Pre-stripped #24 jumper wires for the 16 pin configuration socket for manual configuration of the radio cable pinout. Crystal: Y1 - 12 MHz Crystal - When installing - use supplied plastic spacer, and install tight against board. Transistors: Q1 - 2N2222 Bi-polar NPN Q2 - 2N7000 FET N-Channel Q3 - 2N2222 Bi-polar NPN Q4 - MPSA13 Darlington NPN Q5 - 2N2907 Bi-polar PNP Q6 - 2N2222 Bi-polar NPN Q7 - 2N2907 Bi-polar PNP Q8 - 2N2222 Bi-polar NPN Q9 - 2N2907 Bi-polar PNP Q10 - 2N2222 Bi-polar NPN Q11 - 2N2907 Bi-polar PNP Resistors: All Resistors are 1/8 Watt - Bend leads sharply at body for easier insertion. R1 - 1k R2 - 330 ohm R3 - 1k R4 - 1k R5 - 1 Meg ohm R6 - 22 ohm R7 - 22 ohm R8 - 1.5k R9 - 1k R10 - 1 Meg ohm R11 - 100k R12 - 100k Pot (104) horizontl shaft - panel type (install last) R13 - 4.7k R14 - 10k Pot (103) horizontl shaft - panel type (install last) R15 - 10k R16 - 10k Pot (103) (small - vertical trimmer) R17 - 10k R18 - 4.7k R19 - 10 ohm R20 - 10 ohm R21 - 10k R22 - 10k R23 - 10k R24 - 10k Pot (103) horizontl shaft - panel type (install last) R25 - 1k R26 - 10k R27 - 10k R28 - 1k R29 - 10k R30 - 10k R31 - 10k R32 - 1k R33 - 10k R34 - 10k R35 - 1k R36 - 10k R37 - 10k R38 - 150 ohm R39 - 10k R40 - 470k R41 - 100k NOTE: Components that are supplied on a "carrier" paper should have their leads cut from the carrier near the edge of the paper. Don't try to pull the component away from the carrier paper otherwise you could damage it. NOTE: Some components have pre-bent leads and they'll need to be reformed to allow the part to fully seat on the surface of the circuit board. NOTE: Polarized capacitor locations include a + (plus sign) silkscreened on the board where the positive lead orients. NOTE: Some capacitors have marking on both sides. The marking on one side may not be the value. Turn the component over and read both sides to determine its value. Capacitors: C1 - 47pF small yellow MLCC (marked 47 or 470) C2 - 20pF or 22pF yellow or blue MLCC (marked 20, 200 or 22, 220) C3 - .47uF Tantalum (blue) (observe polarity!) (See below for installation note) C4 - 20pF or 22pF yellow or blue MLCC (marked 20, 200 or 22, 220) C5 - .47uF Tantalum (blue) (observe polarity!) (See below for installation note) C3 and C5 installation note: The positive lead is on the right side when the printing is facing you. C3 is installed so its printing faces C2. C5 is installed so its printing faces AWAY FROM C4. C6 - 10uF electrolytic (observe polarity!) C7 - 10uF electrolytic (observe polarity!) C8 - 10uF electrolytic (observe polarity!) C9 - 47pF small yellow MLCC (marked 47 or 470) C10 - 4.7uF small electrolytic (observe polarity!) C11 - 4.7uF small electrolytic (observe polarity!) C12 - 4.7uF small electrolytic (observe polarity!) C13 - 4.7uF small electrolytic (observe polarity!) C14 - 4.7uF small electrolytic (observe polarity!) C15 - .1uF .1"LS (Marked "104")(small yellow) C16 - 47pF small yellow MLCC (marked 47 or 470) C17 - 100uF Tantalum (yellow marked "107") (observe polarity - printing faces Q2) C18 - .047uF .2"LS ceramic MLCC with wider spaced leads and larger body as compared to C23 and C24 C19 - 4.7uF small electrolytic (observe polarity!) C20 - 47pF small yellow MLCC (marked 47 or 470) C21 - 4.7uF small electrolytic (observe polarity!) C22 - 4.7uF small electrolytic (observe polarity!) C23 - .047uF .1"LS (small blue or yellow - marked 473) C24 - .047uF .1"LS (small blue or yellow - marked 473) C25 - 100uF (polarized electrolytic) (observe polarity!) C26 - 100uF NON-POLAR (larger black electrolytic) (can be installed either way) C27 - 100uF (polarized electrolytic) (observe polarity!) C28 - 100uF NON-POLAR (larger black electrolytic) (can be installed either way) C29 - 10uF NON-POLAR (small black electrolytic) (can be installed either way) C30 - .01uF .1"LS (Marked "103")(small yellow) C31 - 1uF Tantalum (green or yellow marked "105") (observe polarity - printing faces C15 and C30) C32 - 1uF Tantalum (green or yellow marked "105") (observe polarity - printing faces C22) C33 - 47pF small yellow MLCC (marked 47 or 470) Power Switch: SW1 - DPDT push-button locking type with white button (cap) DRA-SR-RJ45 REV1 or later printed circuit board LS = Component Lead Spacing - .1 inches = 2.54mm MLCC = Multi-Layer Ceramic Capacitor